Poulan 437921 Manuale Utente

OWNER'S MANUALMODEL NUMBER:PP291E27SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the O

10The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety gla

11OPERATIONTO THROW SNOW (See Fig. 14)The auger rotation is controlled by the auger control lever located on the right side handle.• Squeeze auger co

12TO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are located on each

13OPERATIONTO START ENGINE • Be sure fuel shut-off valve is in the “OPEN” position.Your snow thrower engine is equipped with both a 120 Volt A.C. ele

14MAINTENANCELUBRICATION CHARTGENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator

15MAINTENANCEV-BELTSCheck V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not ad just abl

16SERVICE AND ADJUSTMENTSWARNING: To avoid serious injury, before performing any service or ad just ments:1. Be sure the on/off switch is in the OFF p

17SERVICE AND ADJUSTMENTS8. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.HINT: Insert a 3/8"

18SERVICE AND ADJUSTMENTSTO ADJUST CABLE TENSION (See Fig. 23)Adjust cable tension by turning the adjuster turn buckle, located on the right hand cabl

19STORAGEImmediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.WARNING: Never

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20TROUBLESHOOTINGDoes not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2.

21NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

22REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inch

23NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

24KEY PART NO. NO. DESCRIPTION1233401.11.001-B4KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inche

25KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

26NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

27NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

28NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

36. When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel-ler and all moving parts have stopp

30NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

31KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

32REPAIR PARTS SNOW THROWER - MODEL NUMBER PP291E27 (96198003602)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPOR

33NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

34KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONNOTE: All component dimensi

35NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

36NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

37KEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTIONKEY PART NO. NO. DESCRIPTION01.14.009-A11 422663 SAF

38KEY PART NO. NO. DESCRIPTIONNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipm

39SERVICE NOTES

4PARTS PACKED SEPARATELY IN CARTONRead these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thro

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-als and

5ASSEMBLY / PRE-OPERATIONSPEED CON TROL RODSPEED CONTROL BRACKETRETAINER SPRINGSPEED CONTROL LEVERFig. 2SPEEDCONTROL RODHANDLE KNOBLOWER HANDLEPLASTIC

6ASSEMBLY / PRE-OPERATIONAUGERCONTROL LEVERAUGER CONTROL RODAUGERCONTROL BRACKETRETAINER SPRINGFig. 6INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)1.

7ASSEMBLY / PRE-OPERATIONCHECK TIRE PRESSUREThe tires on your snow thrower were overinflated at the fac-tory for shipping purposes. Correct and equal

8OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

9OPERATIONDrive speed control lever - used to select forward or reverse motion and speed of snow thrower.Traction drive control lever - used to engage